Mazda Crib Toy 4112A NZLCTHL3 User Manual

9. Return to the vehicle and firmly press,  
hold for 2 seconds and release the  
programmed HomeLink® button. Fig. 5  
10. Repeat Step 9 a second time and  
possibly a third time (depending on  
brand of device).  
Auto-Dimming Mirror User Guide  
Hold for 2 seconds and  
release  
Congratulations! Your new Mazda is equipped with an Automatic-Dimming Mirror,  
manufactured by Gentex Corporation. During nighttime driving, this safety feature will  
automatically detect and eliminate dangerous rearview mirror glare.  
HomeLink® should now activate your  
rolling code equipped device.  
Fig. 5  
Your new mirror may or may not have all of the features shown in this User Guide.  
Please refer only to the sections that pertain to the model mirror you have in your new  
vehicle.  
Gate Operator / Canadian Programming:  
Canadian radio-frequency laws require transmitter signals to “time-out” or quit after  
several seconds of transmission – which may not be long enough for HomeLink® to pick  
up the signal during programming. Similar to this Canadian law, some U.S. gate  
operators are designed to “time-out” in the same manner.  
Auto-Dimming Mirror with Compass  
DISPLAY
WINDOW  
ON/OFF  
BUTTON  
If you live in Canada or you are having difficulties programming a gate operator by using  
the “Programming” procedures (regardless of where you live), replace “Programming  
HomeLink® step 4 with the following:  
NOTE: If programming a garage door opener or gate operator, it is advised to unplug  
the device during the “cycling” process to prevent possible overheating.  
LED  
SENSOR  
To Operate the Auto-Dimming Feature:  
4. Continue to press and hold the HomeLink® button while you press and release  
- every 2 seconds (“cycle”) your hand-held transmitter until the frequency signal  
has successfully been accepted by HomeLink®. (The indicator light will flash  
slowly and then rapidly.)  
Push the “ ” switch to turn the mirror on/off. The auto-dimming feature is  
enabled when the green LED indicator is on.  
To Operate the Compass Feature:  
Proceed with “Programming” step 5 to complete.  
1. Push the display “ ” switch. The vehicle’s directional heading will be displayed.  
2. Pushing the “ ” switch a second time will turn off the visual display.  
3. If the display reads “C”, calibrate the compass by driving the vehicle in up to 3  
complete circles at less than 5 MPH.  
NOTE: Programmed HomeLink® codes can be intentionally erased (when selling  
vehicle etc.) by holding the 2 outer buttons (as shown in Fig. 1) for 20 seconds until LED  
indicator begins to flash. Do not hold buttons for more than 30 seconds.  
If you have any questions or are having difficulty programming your  
HomeLink® buttons, please refer to www.homelink.com or call  
1-800-355-3515.  
CALIBRATION PROCEDURE  
Cleaning the mirror:  
When cleaning the mirror, use a paper towel or similar material dampened with  
glass cleaner. Do not spray glass cleaner directly onto the mirror as damage to  
internal circuitry may result.  
4. To adjust for compass variance:  
a. Press the “ ” button for more than 9 seconds, or until the current zone  
number appears in the display.  
b. Find your current location and variance zone number on the zone map below.  
c. Press the “ ” button until the new zone number appears in the display.  
After you stop pressing the button, the display will show a compass heading  
within a few seconds.  
Troubleshooting Guidelines:  
1. “C” or “CAL” is displayed in the display window  
a. Perform calibration procedure.  
2. Inaccurate compass direction  
a. Perform compass zone setting procedure and then calibration procedure  
b. Vehicle magnetics may have changed.  
- Press and hold the “ ” button or the “ ” button (if mirror has) for 9  
seconds until a “C” or “CAL” appears in the display window.  
- Perform calibration procedure.  
NOTE: Installing items such as a ski rack, antenna, luggage rack or recent body  
repair can cause changes to the vehicle’s magnetic field. This may require  
that the compass be recalibrated by performing the recalibration procedure.  
3. The temperature display is reading significantly low  
a. The temperature display may have been changed to degrees Celsius. Refer  
to the section of this User Guide pertaining to the temperature feature to  
correct.  
4. The display window shows “SC” or “OC” instead of temperature  
a. These problems must be corrected at your authorized Dealer Service Center.  
FCC: NZLCTHL3. IC: 4112A-NZLCTHL3  
550-0351 B  
 

Lenovo Personal Computer Z61 User Manual
Lenoxx Electronics Boiler COWB2 User Manual
LG Electronics DVD Player DN191H User Manual
LG Electronics Flat Panel Television 22LB4510 User Manual
Lowrance electronic SONAR X52 User Manual
Makita Cordless Saw JR3050T User Manual
Makita Sander 9040L User Manual
McIntosh Stereo System M85 User Manual
Memorex VCR MVR4042 User Manual
Microsoft Server Windows NT 40 User Manual