INSTALLATION INSTRUCTIONS FOR PART 99-7511S
APPLICATIONS
Mazda 6 2009
99-7511S
KIT FEATURES
• DIN Radio Provision
• ISO Mount Radio Provision
• Double DIN Radio Provision
• Stacked ISO Mount Radio Provision
• Painted To Match Silver Factory Dash
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket • G) Filler Trim Panel • H) (2) #3 3/8” Phillips Screws
C
B
A
H
F
E
G
D
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932
© COPYRIGHT 2009 METRA ELECTRONICS CORPORATION
99-7511S DASH DISASSEMBLY
MAZDA 6 2009
A
Disconnect the negative battery
1
terminal to prevent an accidental
short circuit.
2
3
Unclip and remove the cup
holder/parking brake trim panel.
(Figure A)
Unclip and remove the trim panel
above the glove box and down the
right side of the center console.
(Figure B)
4
5
Unclip and remove the trim panel next
to the key switch and down the left
side of the center console. (Figure B)
B
Unclip and remove the trim panel
surrounding the climate controls and
the shifter lever. (Figure C)
6
7
Unclip and remove the vent panel
above the radio. (Figure D)
Remove (4) screws securing the
factory radio. Unplug and remove the
radio.
Continue to kit preparation
C
D
1
99-7511S KIT ASSEMBLY
DIN RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
2
Attach the filler trim panel to the back
of the radio housing at the bottom
edge. (Figure A)
REAR OF RADIO HOUSING
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure B)
FILLER TRIM PANEL
3
4
Slide the aftermarket radio into the DIN
cage until it snaps into place. (Figure C)
Snap the pocket into the the bottom
opening of the radio housing.
B
(Figure D)
Continue to final assembly.
D
C
2
99-7511S KIT ASSEMBLY
ISO MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Attach the filler trim panel to the back
of the radio housing at the bottom
1
2
edge. (Figure A)
REAR OF RADIO HOUSING
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure B)
FILLER TRIM PANEL
3
4
5
Slide the radio into the radio housing
until it snaps into place. (Figure C)
Snap the Trim Plate onto the front of
the Radio Housing. (Figure C)
B
Snap the pocket into the bottom open-
ing of the radio housing. (Figure D)
Continue to final assembly.
D
C
3
99-7511S KIT ASSEMBLY
DOUBLE DIN/STACKED ISO MOUNT
UNIT(S) PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Attach the filler trim panel to the back
of the radio housing at the bottom
1
edge. (Figure A)
REAR OF RADIO HOUSING
2
3
Cut and remove the center bar from
the Radio Housing. (Figure B)
Snap the Double DIN brackets to the
inside edge of the Radio Housing.
FILLER TRIM PANEL
(Figure C)
B
4
Slide the Double DIN or stacked ISO
mount unit(s) into the bracket/radio
housing assembly and secure to the
assembly using the screws supplied
with the unit(s). Snap the DDIN Trim
Plate onto the front of the Radio
Housing. (Figure D)
Continue to final assembly.
D
C
4
99-7511S FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
Enjoy your newly installed radio!
5
99-7511S INSTRUCTIONS
1-800-221-0932
Rev. 01/13/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION NST99-7511S
|